Cooling Systems & Fans

110v Low Noise Cooling Fan - Sold in the USA Only
Aluminum Casing - Polycarbonate Impeller - Ball Bearings

Fan Cord sold separately

Cooling Fan 210/240v 50/60Hz 14.5/12.5W 2200/2400 RPM Impedance Protected

114.3mm Diameter Fan Guard for P1800 and 8700 Fans

Innovative Design Enables Quiet and Efficient Ventilation
The innovative design of the fan blades improves the airflow and facilitates a highly efficient ventilation. The impeller was designed with a focus on minimizing the noise level yet delivering the desired airflow and pressure. This is the quietest fan on the market!

Long Service Life
The Fluid Dynamic Bearing comes with an oil capsule that avoids lubricant leakage. Thus this bearing is as quiet as a sleeve bearing but comes with a significantly higher service life.

Two Way installation
Mount to extract hot air or reverse mount to draw in cool air

Comes with 4 screws and 3-pin socket connector
Noise Level: 0.3 Sone (@ 1,350 RPM)

Performance
Fan Speed:
- 1,350 RPM (@ 12V DC)
- 900 RPM (@ 7V DC)
- 650 RPM (@ 5V DC)
Air Flow: 53CFM (90.1 m3/h)

Electrical Characteristics
Typical Voltage: 12V DC
Start-up Voltage: 2.7V DC
Cable Length: 400mm

Connection
Motherboard: +12V DC
3-pin socket

Penn Elcom brings you a new and quiet exhaust fan unit for flight case racking that is mounted into a Penn Elcom large dish for your convenience.

The FT80-Q-FC regulates the enclosure’s temperature by expelling hot air, preventing thermal failure. Thermal failure is caused by many generic in-board fans that simply circulate hot air within the enclosure rather than expelling it.

- Low noise level 22.5dBA (0.3 sone)
- Dimensions: 178mm x 127mm x 47.5mm / 7" x 5" x 1.87"
- 28CFM (47.6m³/h) at 2000 RPM
- High static pressure
- 1 x 9 bladed 80mm / 3.15" fan
- 12V DC - 200mA
- 2 x DC in/out sockets
- Temperature sensor socket
- 500mA universal PSU supplied
- Combined weight of 400g / 0.88Lb
- Fluid bearings = 2 year limited warrantee


A second unit can also be run from the 500mA power supply by using a CRC-LINK cable.

Thermal sensor accessory included, the CRC-TEMP can be Plugged into the TEMP socket.

Quiet exhaust fan unit designed to be fitted into sealed wooden cabinets, closets and enclosed equipment racks where hot air is not being expelled. These type of situations invariably cause thermal failure, as the in-board fans are just recycling hot air.

These exhaust fans are easily fitted into any wooden enclosures all that is required is a an awl, cross head screwdriver and a 79mm / 3 1/8" Hole Cutter.

Once mounted just hook-up to the 12V universal PSU via the input socket.
A second unit can also be run from the 500mA power supply by using a CRC-LINK cable.

A thermal sensor accessory, the CRC-TEMP can be Plugged into the TEMP socket.

Technical Specifications:
· Dimensions: 100mm x 100mm x 25mm / 4" x 4" x 1"
· Low Noise 22.5dBA (0.3 Sone)
· 28CFM (47.6m³/h) @2000 RPM
· High Static Pressure
· 1 x 9 Bladed 80mm Fan
· 12V DC - 200mA
· 2 x DC In/Out Sockets
· Temperature Sensor Socket
· DC in/out sockets
· 500mA universal PSU supplied
· Mounting Holes align with attached fitting template

· Fluid Bearings = 2 Year Limited Warrantee